Manitex 26101 C Stand-Up Control

Manufacturer Manitex
Model 26101 C
Capacity 26 US Tons
Main Boom 101 ft.

READ MORE >

Category:

Description

26101C General Specifications
Nominal Rating 26 tons @ 5′
Maximum Tip Height 141′ 4″ (43,1 m)
Maximum Jib Length 29,4′
Quick Reeve Boom Point STD
Capacity Alert System LMI
Overload Shut-Off STD
Total Crane Weight

BOOM
Inverted T-cross section, 4-section telescoping type, extended and retracted proportionally by double-acting hydraulic cylinder and cable-crowd system. 4-section
29′ 5.25″ (9,0 m) to 101′ 5.25″ (30,9 m). Maximum main boom tip height 112′ 2″(34,2 m). 1-section, 29′ (8,8 m) jib. Maximum tip height 141′ 4″ (43,1 m).

Boom Points – Three high-density nylon sheaves mounted on heavy-duty roller bearings. Two removable pin-type rope guards. Quick-reeve boom point on 101′ boom.

Boom Elevation – Double-acting hydraulic cylinder. Working range from 9.5° below horizontal to 80.5° above.

Load Hook – 5-ton capacity hook with heavy-duty swivel and weight is provided for single-line operation.

HOIST
Maximum theoretical line speed 247 fpm (75,3 mpm). Maximum theoretical bottom-layer line pull 12,000 lbs (5 443 kg). Two-speed planetary reducer. Spring-applied, pressure-released internal brake. Wet multi-disc internal brake is spring-applied, pressure-released.

Wire Rope – 300 feet (91,4 m) of 9/16″ (14,3 mm) diameter 6 x 25 EIPS IWRC.

SWING SYSTEM
Externally mounted, double-reduction planetary driven by hydraulic motor. Maximum theoretical swing speed 1.5 rpm. Wet multi-disc internal brake is spring applied, pressure released. Oversized diameter ball bearing swing circle with external gear. 372° non-continuous rotation.

OUTRIGGERS
21′ 6″ (6,6 m) Extended A-frame link type. Operated independently for precise leveling. Equipped with double-acting
hydraulic cylinders.

MOUNTING
Pedestal and subframe are mounted to chassis by threaded rods and clamp plates. No welding, drilling or bolting to truck frame is required.

A-Frame Stabilizers – 8′ (2,4 m) retracted; 10′ (3,1 m) extended. Operated independently for precise leveling. Double-acting hydraulic cylinders. Fixed pad size is 8″ (203,2 mm) x 11.375″ (288,9 mm).

Subframe – Torsionally resistant, rigid 4-plate design, mounted under crane full length of truck frame.

Rear Underride Protection – Supplied on factory-mounted cranes. Fabricated structure mounted under rear of bed. Complies with Bureau Motor Carrier Safety Standard 393.86.

Boom Rest – Heavy-duty, fabrication. Easily removed to simplify loading and unloading truck deck.

CONTROL SYSTEM
Dual operator platforms are equipped with four single-lever crane controls arranged to ANSI B30.5 standards. Fully proportional control valves and system pressure gauge. Each station also includes outrigger and stabilizer controls, engine start/stop, foot throttle, signal horn, boom-angle indicator, bubble levels, load charts, range diagram and audio and/or visual indicators to warn operator of overload condition.

HYDRAULICS
Hydraulic System – A 3-section vane pump direct-mounted to power take-off on truck transmissions provides 35 gpm (133 lpm) to the hoist, 8 gpm (30 lpm) to the swing circuit and 18 gpm (68 lpm) to the remaining crane functions. A 70-gallon (265-liter) baffled reservoir includes a 25-micron return line filter and magnetic plug. A single gate valve on the suction line from the tank to pump. Extensive use of SAE O-ring face seal hydraulic fittings where possible.

Hydraulic Cylinders – All load-holding cylinders are equipped with integral holding valves.

WARNING SYSTEMS
Load Moment Indicator – Senses boom hoist cylinder pressure, boom length and boom angle. Audio-visual warning indicates overload conditions and overload shutoff feature prevents continuing overload. Operator can access all relative crane configuration and load conditions via display at the operator station.

Anti-Two-Block System – Audible warning and shutoff functions prevent hook from contacting boom point.

Back-Up Alarm – Supplied on factory-mounted cranes, electronic audible motion alarm activated when truck transmission is in reverse gear.

Download 26101 C Specs

Download 26101 C Load Charts

Download 26101 C Load Charts (Spanish)

Additional information

Manufacturer

Manitex

Model

26101 C

Capacity

26 US Tons

Main Boom

101 ft.

Max Tip Height

142 ft.

Additional Features

26 ton (23 mton)capacity

4-section,101'(30,8 m) proportional boom

112'2"(34,2 m)maximum main boom tip height

141'4"(43,1 m)maximum tip height

1-section jib

2-speed planetary hoist with grooved drum and negative draft flange

Load moment indicator with digital display and overload shutdown Removable boom rest

21'6"(6,6 m)A-frame outriggers

System pressure gauge

Rugged,weatherproof,automotive style electrical system

For More Information:

Please fill out our "Contact Us" form on our contact page and mention the equipment Make and Model in the subject line.