Manitex 3000 Series Stand-Up Control

Manufacturer Manitex
Model 3000 Series
Capacity 30 US Tons
Main Boom Up to 102 ft.




Inverted T-cross section, 4-section telescoping type, extended and retracted proportionally by a double-acting hydraulic cylinder and cable-crowd system. Easily replaceable and adjustable high-density nylon slide pads.

30102 – 4-Section 30′ (9,1 m) to 100′ (30,5 m). 2-section, 26′ (7,9 m) to 46′ (14,0 m) jib.

Quick Reeve Boom Point – Two high-density nylon load sheaves mounted on heavy-duty roller bearings. Two removable pin-type rope guards.

Boom Elevation – Double-acting hydraulic cylinder. Working range from 9Þ below horizontal to 80.6Þ above.

Load Hook – 7-ton (6,4 mton) capacity hook with heavy-duty swivel and weight is provided for single-line operation.

Maximum theoretical line speed 247 fpm (75,3 mpm). Maximum theoretical bottom-layer line pull 11,500 lb (2 227 kg). Two-speed planetary reducer. Wet multi-disc internal brake is spring-applied, pressure-released.

Wire Rope – 335′ (102,1 m) of 9/16″ (14,3 mm) rotation resistant type.

Externally mounted, double-reduction planetary driven by hydraulic motor. Maximum theoretical swing speed 1.5 rpm. Spring-applied, pressure-released parking brake. Ball-bearing swing circle with external gear. 372Þ non-continuous rotation.

A-frame link type with double-acting hydraulic cylinders operated independently for precise leveling. Bubble level located near outrigger controls.

Pedestal and subframe are mounted to chassis by threaded rods and clamp plates. No welding, drilling, or bolting to truck frame is required.

Subframe – Torsionally resistant, rigid 4-plate design. Mounted under crane full length of truck frame.

Rear Underride Protection – Supplied on factory-mounted cranes. Fabricated structure mounted under rear of bed. Complies with Bureau Motor Carrier Safety Standard 393.86.

Boom Rest – Heavy-duty fabrication. Easily removed to simplify loading and unloading truck deck.

Dual operator platforms are equipped with four single-lever crane controls arranged to ANSI B30.5 standards. Fully proportional control valves and system pressure gauge. Each station also includes outrigger and stabilizer controls, engine start/stop, foot throttle, signal horn, boom-angle indicator, bubble levels, beverage container, load chart, and range diagram.

Hydraulic System – A 3-section gear pump direct-mounted to power take-off on truck
transmission provides 32 gpm (133 lpm) to the hoist, 8 gpm (30 lpm) to the swing circuit and 21 gpm to the other crane functions. 70-gallon baffled reservoir includes suction ball valve with strainer two 25-micron filters in the return line. Use of SAE O-ring and face seal O-ring hydraulic fittings throughout system. Aeroquip STC (Snap- to-Connect) on all hoses up to 1″ virtually
eliminates leaks.

Hydraulic Cylinders – All load-holding cylinders are equipped with integral holding valves.

Load Moment Indicator – CAN bus system maximizes expansion capabilities. Senses boom hoist cylinder pressure, boom length and boom angle. Audio-visual warning indicated overload conditions and overload shutoff feature prevents continuing overload. Operator can access all relative crane configuration and load conditions via display at the operator station. Internal boom length cable.

Radio Anti-Two-Block System – Audible warning and shutoff functions prevent hook from contacting boom point. Wireless system minimizes down time typically associated with damaged cables in wired systems.

Back-Up Alarm – Supplied on factory-mounted cranes, electronic audible motion alarm activated when truck transmission is in reverse gear.

Download 3051 C Load Charts

Download 3071 C Load Charts

Download 3071 C Load Rating Chart

Download 30100 C Specs

Download 30100 C Load Charts

Download 30100 C Load Rating Chart

Download 30102 C Load Charts

Download 30102 C Load Rating Chart

Additional information




3000 Series


30 US Tons

Main Boom

Up to 102 ft.

Max Tip Height

Up to 159 ft.

Additional Features

30 Ton (27,3 mton) Capacity

4-Section 100' (30,1 m)

2-Section, 26' (7,9 m) to 46' (14 m) Jib

2-Section, 26' (7,9 m) Fixed Jib

110.6' (33,7 m) Maximum Main Boom Tip Heights

157' (47,8 m) Maximum Tip Height with extension

23.3' 6" (6,8 m) A-frame Outriggers Fully Extended

Optional Out-and-Down Outriggers

14.6' (4,4 m) Out-and-down Rear Stabilizers

2-Speed Planetary Hoist with Grooved Drum and Negative Draft Flange

Wired Load Moment Indicator with crane function cut-offs for overload protection

Externally wired anti-two block system

Rugged, Weatherproof Electrical System with Circuit Status LEDs

Removable Boom Rest

System Pressure Gauge

Clamp-On Mounting

Aeroquip STC (Snap to Connect) Hydraulic Fittings

For More Information:

Please fill out our "Contact Us" form on our contact page and mention the equipment Make and Model in the subject line.